14 Companies Doing An Excellent Job At Patio Door Lock Repair

Patio Door Lock Repairs

Over time, wear and tear can lead to lock malfunctions. There are a few simple steps you can take to ensure the security of your uPVC door.

These simple fixes can make your home safer, whether you realign the lock or clean the mechanism.

Clean the Lock

Although patio doors are a great option to bring the outside in and keep the elements out but they can also pose security risks if your lock isn't working as it should. Over time, wear, tear, hot and cold weather dirt, and other debris can cause your patio door lock to become difficult to operate. With a little effort, you can make sure that your patio door's lock always works correctly.

It is essential to first clean the patio door lock and all moving parts. This will help remove any coatings or dirt that may be preventing your lock from functioning correctly. Begin by wiping the moving parts of the lock for your patio door with a damp, clean cloth. then use a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door and frame that are covered in dirt. Then, wipe the entire lock with dry cloth to get rid of any remaining dampness, and allow it to dry completely before making use of it again.

If your patio door uses pin-tumbler latches, you can apply powdered graphite to the key. You can also use a Teflon lubricant such as WD-40 Multi-Use Product. This kind of lubricant can be applied with ease and will not disintegrate over time. If you are unable to find an appropriate lubricant you could try using a pencil that has a thick tip. Put the pencil in the lock, then shake it to distribute the graphite.

Sliding patio door tracks also require regular maintenance to keep them free of dirt, dust and other debris. These tracks are especially susceptible to snow and ice which can cause them become stuck or slack and make it difficult for your patio doors to open and close.

The sliding rails of the patio door track and rollers can be cleaned by removing any dirty or damaged weather stripping and then cleaning it, before replacing it. The rollers of patio doors can be cleaned and sprayed with an oil that is nonstick.

Lubricate the moving parts

uPVC french doors, like sliding patio doors, work by using 3 to 4 or sometimes 5-point locking mechanisms which include the handle and lock cylinder controlled by a key. They require maintenance and oiling of the moving parts. This can be done with the use of a thin oil however, never WD40. This should be done every year, at a minimum.

If sagging hinges aren't the cause, the door could be misaligned and caught or striking the strike plate's hole in the frame. The solution is to take off the strike plate and companies use an abrasive chisel, which will enlarge the mortise that it rests in. This lets the latch sit properly in the hole and avoids scratching or catching on the frame.

Find the length of the cylinder using an object of book or wood that can be inserted into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw until the end cylinder.

Check the lock's width

If your patio screen door repair near me door latch is difficult to turn even after cleaning and oiling it could be because it's not aligned with the strike plate. Make sure that your door is balanced, and if the hinge screws are in good condition. In most instances, moving the strike plate downwards or upwards could fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to engage. In this case, enlarge the opening using the hammer and chisel. Then, test the latch to ensure that it doesn't rub against the door jamb frame or catch the frame.

Before you purchase a replacement lock, it is important to identify the type of mortise lock you currently have. You can do this by looking at the faceplate on the lock and determining whether it is square or round. Then, look at the screw holes in the existing lock and note the dimensions of each one. This will enable you to locate the replacement lock that has exactly the same width and fits into your existing hole.

You'll want to identify the mortise lock and inspect it for scratches, bends or other damage that need to be fixed. A damaged or bent latch is more likely than one that has been used a lot to break. Replace the lock if you notice indications of damage.

Once you've inspected the lock and identified which type of replacement you'll need now is the time to start working on the actual repair. Remove the handle and spindle out of your patio door, and then insert the new one. Begin by installing the interior handle. Align it with the spindle, and then secure it into position using two bolts or screws. Install the exterior handle after the interior handle. Once you have completed these steps, test the handles to make sure that they are able to open and close easily and that the latch is in contact correctly with the strikeplate.

Check the door's Strike

The door latch and strike plate are two parts of the lock that work together to ensure that the latch locks the door. If these are misaligned and the latch isn't latching the door shut correctly. Fortunately, this problem is usually easy to correct.

Examine the holes that receive the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Then loosen the screws that keep the strike plate in place, allowing it to move vertically but not separating it from the frame of your door. Adjust the strike plate to align its holes for receiving with latch hooks of the door latch. Once the strike plate is adjusted then tighten the screws and test the door to see whether it shuts easily with the new adjustment.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, but they're crucial to lock and unlock your door. The metal plates are situated on the top and bottom jambs of your door, which are where they help support the latch. The door latch slides onto the strike plate, and it creates a seal. If the strike plate has been damaged, rusted, or is not installed correctly, the latch may not lock the door properly.

One common reason for the patio door repair near me door lock to stick or not close is a misalignment between the latch and strike plate. This can be verified using the "lipstick" test. Apply a little lipstick across the edge of the deadbolt. Then cover it with masking tape. The lipstick will leave a mark when you close the door. This will show you exactly where the latch joins the strike plate. If the mark is too high or low, you can alter the strike plate.

Sliding patio glass repair near me door locks help keep your home safe from burglars. If they're not functioning properly, you need to solve the issue fast. By following these easy steps, you'll be able to fix your patio door's lock and restore its functionality in no time.